nForce4 SLI Roundup: Painful and Rewarding
by Wesley Fink on February 28, 2005 7:00 AM EST- Posted in
- Motherboards
Gigabyte K8NXP-SLI: Overclocking and Stress Testing
FSB Overclocking Results
| Front Side Bus Overclocking Testbed | |
| Gigabyte K8NXP-SLI | |
| Processor: | Athlon 64 4000+ (2.4GHz, 1MB Cache) |
| CPU Voltage: | 1.55V (default 1.50V) |
| Cooling: | Thermaltake Silent Boost K8 Heat sink/Fan |
| Power Supply: | OCZ Power Stream 520W |
| Memory: | OCZ PC3200 EL Platinum Rev. 2 (Samsung TCCD Memory Chips) |
| Hard Drive: | Seagate 120GB 7200RPM SATA 8MB Cache |
| Maximum OC: (Standard Ratio) |
230x12 (4X HT, 2.5-3-2-7, 1T, 2.8V) 2760MHz (+15%) |
| Maximum FSB: (Lower Ratio) |
230x12 (2760MHz) (4X HT, 2.5-3-2-7, 2.8V) (1:1 Memory, 1T, 2 DIMMs in DC mode) (+15% Bus Overclock) |
After the excellent overclocking results that we found in our pre-production review of the K8NXP-SLI, we really expected the Gigabyte SLI to be near the top of our overclocking charts. However, something has happened along the way from pre-production to production because our production board could only reach a very disappointing 230 CPU speed regardless of the multiplier selected. This is in stark contrast to the 284 that we easily reached on the pre-production board.
We recently met with Gigabyte to discuss this issue and Gigabyte has assured us that they will make updates to get overclocking back to the levels which we saw in our earlier review. For now, we can only say that we have no idea what you will actually find in the overclocking capabilities of a K8NXP-SLI that you might buy. It could be stellar, like the pre-production board that we tested, or mediocre, like the last board that we tested. We have evidence to support either conclusion.
Memory Stress Test Results:
Our memory stress tests measure the ability of the K8NXP-SLI to operate at its officially supported memory frequency (400MHz DDR), at the lowest memory timings that OCZ PC3200 Platinum Rev. 2 modules will support. All DIMMs used for stress testing were 512MB double-sided (or double-bank) memory. To make sure that memory performed properly in Dual-Channel mode, memory was only tested using either one dual-channel (2 DIMMs) or 2 dual-channels (4 DIMMs).| Stable DDR400 Timings - One Dual-Channel (2/4 DIMMs populated) |
|
| Clock Speed: | 200MHz |
| CAS Latency: | 2.0 |
| RAS to CAS Delay: | 2T |
| RAS Precharge: | 7T |
| Precharge Delay: | 2T |
| Command Rate: | 1T |
Using two DIMMs in Dual-Channel 128-bit mode, the memory performed in all benchmarks at the fastest 2-2-2-7 timings, at default 2.6 voltage.
Tests with 4 DS DIMMs on an AMD Athlon 64 system are more demanding, since AMD specifies DDR333 for this combination. However, most AMD Athlon 64 motherboards combined with recent AMD processors (the memory controller is on the AMD CPU) have been able to handle 4 DIMMs at DDR400.
| Stable DDR400 Timings - 4 DIMMs (4/4 DIMMs populated) |
|
| Clock Speed: | 200MHz |
| CAS Latency: | 2.0 |
| RAS to CAS Delay: | 2T |
| RAS Precharge: | 7T |
| Precharge Delay: | 2T |
| Command Rate: | 2T |
Tests with all four DIMM slots populated on the Gigabyte required a 2T Command Rate with 4 DIMMs in two dual channels. This is the pattern seen on other top-performing Socket 939 boards. There was no problem running 4 DS DIMMs at DDR400 at the same aggressive 2-2-2-7 settings, which worked well with 2 DIMMs.
Facebook
Twitter
RSS
108 Comments
View All Comments
Heinrich - Monday, February 28, 2005 - link
Hi, this is a great article. I'm really disappointed that the issues with the new Winchesters and the MSI board were not uncovered. The new CPUs will not post past FSB of 219, which is far below the 250 many get with other boards. Someone with the depth of knowledge, experience, and understanding of all these little options in the BIOS could help us uncover the real problem. Here's the best thread devoted specifically to the problem on Rebel HQ:http://www.rhcf.com/sisubb/ultimatebb.php/topic/21...
ajmiles - Monday, February 28, 2005 - link
Hey,I enjoyed the round up of the SLI boards very much and thought it was very thorough.
I own an A8N SLI Deluxe board, and too have been thoroughly disappointed with it's overclocking performance.
On behalf of tens of users on the Anandtech - Motherboards forums, would it be beyond Anandtech's power to get a statement from Asus about the issue???
At a 2T Command Rate the board will overclock to 316, 1T however just 249. The sudden BSODing as you approach 250 smacks of something that could be fixed with a BIOS update.
Please Anandtech, A8N users are begging for this to be fixed, or at least be told it can't be.
Many thanks, and again, a great article.
Adam Miles
Viper4185 - Monday, February 28, 2005 - link
is it true that the MSI board doesnt have a PCI Express x1 slot so that when the new Creative PCI express sound cards come out it wont fit?Viper4185 - Monday, February 28, 2005 - link
Thanks for the review guys, just what I wanted! Although I am interested in the Ultra versions its still very similar...I was wondring if you could comment on the stability/stress testing of the DFI board as Hardocp seems to have had some issues...
http://www.hardocp.com/article.html?art=NzE3LDc=
Also would have been good if you included the Abit Fatal1ty board to make the review 100% conclusive for me.
nzimmers - Monday, February 28, 2005 - link
dang, I wasn't first, oh well.one more thing....I no longer chase the FPS demon, and I am better for it (mentally and emotionally). To be honest I don't expect SLI to become a standard in MB design.....even for high end gamers. Isn't the price just too high?
nzimmers - Monday, February 28, 2005 - link
First post!I was actually really (plesantly) surprised that DFI did so well. I know that they have been improving lately but isn't it great to see another MB manufacturer improving for once?
arfan - Monday, February 28, 2005 - link
finally...., thx 4 your reviewjkv71 - Saturday, June 3, 2017 - link
My DFI video quit. I use an adapter to run hdmi on my tv. I replaced the video card and still nothing. I replaced the mother board. Still nothing. Any ideas?