Scythe Ninja Plus Rev. B: Updated Cooling Legend
by Wesley Fink on April 11, 2007 2:00 AM EST- Posted in
- Cases/Cooling/PSUs
Final Words
Scythe's Ninja Plus Revision B is an update to a long-running and well-regarded heatpipe tower cooler. The design mounts six u-shaped heatpipes in three heatpipe clusters on each side of a square fin tower. The fin tower has slots for mounting clips on each side, which means up to 4 cooling fans can be mounted. The kit ships with one low-noise 120mm fan of moderate 49.6 CFM output.
The Ninja Plus B comes with easy to install mounts for Intel socket 775, AMD AM2/939/940/754 and the older Intel socket 478. The 775 mount uses push clips for mounting just like the Intel stock design, but this also brings concerns about a large, heavy cooler being mounted with such a flimsy connector, which was clearly intended for lighter weight coolers. We have had no problems with stressing the motherboard or falling coolers in vertical towers, but we strongly recommend that this is not a mount design for a LAN Party PC that will be moved frequently.
With the stock low-noise fan the performance of the Ninja was about the same as the Scythe Infinity - average but not chart-topping - with a maximum OC of 3.83GHz. However, like the Infinity, the Ninja has very flexible options for mounting 1-4 fans and performance with two standard Scythe fans in a push-pull arrangement reached 3.90GHz. This places the Ninja in the top tier of coolers we have tested.
The Ninja Pus B also managed to reach a 3.90GHz stable overclock with a single, higher output SilenX fan specified as 72 CFM/14 dB-A. Cooling performance and overclocking with the single SilenX fan were virtually the same as results with a dual fan push-pull using two of the low noise Scythe fans. With both the Scythe and SilenX fans cooling the Ninja Plus B noise levels remained below the noise floor of the system.
Cooling and overclocking tests were also run with two 72 CFM SilenX fans in a push pull arrangement on the Ninja Plus B. The highest stable overclock with this combo remained at 3.90GHz - there was no improvement in overclocking ability. However, two SilenX fans in push-pull cooled about 2C better at idle and load than a single SilenX fan or two Scythe fans in push-pull configuration.
As packaged the Scythe Ninja Plus B is a competent and quiet cooler. The Scythe kit is a more effective cooler than the similar OCZ Vindicator, but neither kit is chart topping. Swap the stock fan with a SilenX 72 CFM/14 dB-A fan, however, and the Ninja Plus B is then able to overclock to 3.90GHz, matching the best heatpipe towers we have tested. Comparing results of the Scythe Ninja Plus B with the SilenX to the OCZ Vindicator with the same fan proves rather conclusively that the OCZ Vindicator is not just a relabeled Ninja Plus B. The Scythe cooler does a better job of cooling with the same fan, and while the coolers may look the same, the Ninja is definitely the more effective cooler.
With results of the Scythe infinity and Scythe Ninja Plus B so similar in our tests, it is fair to ask which cooler is the better choice. That is a hard question to answer, but the Infinity is a little more compact in most cases and cools just as well as the large square Ninja. The choice depends on your preferences and the board/case that will be used with the cooler. However, both the Ninja Plus B and the Infinity are just good, quiet coolers with the shipping kit fans - they are not particularly great for overclocking. Add a quiet high output fan like the SilenX or use two Scythe fans in a push-pull configuration, and both coolers compete with the best we have tested. The Tuniq Tower 120 and Thermalright Ultra 120 still cool a bit better at most settings, but they reach the same overclock as the Ninja and Infinity with push-pull fans or a SilenX.
The Thermalright Ultra 120 Extreme remains the best air cooler we have tested so far, reaching a 3.94GHz overclock at low temperatures with a Scythe SFLEX fan. The Scythe Ninja Plus B joins the top tier of coolers just below this with the Thermalright Ultra 120, Tuniq Tower 120, OCZ Vindicator with SilenX fan, and Scythe Infinity push-pull. In any of the tested configurations it is a quiet and effective cooler, with best cooling results with a high output fan or push-pull fans.
Scythe's Ninja Plus Revision B is an update to a long-running and well-regarded heatpipe tower cooler. The design mounts six u-shaped heatpipes in three heatpipe clusters on each side of a square fin tower. The fin tower has slots for mounting clips on each side, which means up to 4 cooling fans can be mounted. The kit ships with one low-noise 120mm fan of moderate 49.6 CFM output.
The Ninja Plus B comes with easy to install mounts for Intel socket 775, AMD AM2/939/940/754 and the older Intel socket 478. The 775 mount uses push clips for mounting just like the Intel stock design, but this also brings concerns about a large, heavy cooler being mounted with such a flimsy connector, which was clearly intended for lighter weight coolers. We have had no problems with stressing the motherboard or falling coolers in vertical towers, but we strongly recommend that this is not a mount design for a LAN Party PC that will be moved frequently.
With the stock low-noise fan the performance of the Ninja was about the same as the Scythe Infinity - average but not chart-topping - with a maximum OC of 3.83GHz. However, like the Infinity, the Ninja has very flexible options for mounting 1-4 fans and performance with two standard Scythe fans in a push-pull arrangement reached 3.90GHz. This places the Ninja in the top tier of coolers we have tested.
The Ninja Pus B also managed to reach a 3.90GHz stable overclock with a single, higher output SilenX fan specified as 72 CFM/14 dB-A. Cooling performance and overclocking with the single SilenX fan were virtually the same as results with a dual fan push-pull using two of the low noise Scythe fans. With both the Scythe and SilenX fans cooling the Ninja Plus B noise levels remained below the noise floor of the system.
Cooling and overclocking tests were also run with two 72 CFM SilenX fans in a push pull arrangement on the Ninja Plus B. The highest stable overclock with this combo remained at 3.90GHz - there was no improvement in overclocking ability. However, two SilenX fans in push-pull cooled about 2C better at idle and load than a single SilenX fan or two Scythe fans in push-pull configuration.
As packaged the Scythe Ninja Plus B is a competent and quiet cooler. The Scythe kit is a more effective cooler than the similar OCZ Vindicator, but neither kit is chart topping. Swap the stock fan with a SilenX 72 CFM/14 dB-A fan, however, and the Ninja Plus B is then able to overclock to 3.90GHz, matching the best heatpipe towers we have tested. Comparing results of the Scythe Ninja Plus B with the SilenX to the OCZ Vindicator with the same fan proves rather conclusively that the OCZ Vindicator is not just a relabeled Ninja Plus B. The Scythe cooler does a better job of cooling with the same fan, and while the coolers may look the same, the Ninja is definitely the more effective cooler.
With results of the Scythe infinity and Scythe Ninja Plus B so similar in our tests, it is fair to ask which cooler is the better choice. That is a hard question to answer, but the Infinity is a little more compact in most cases and cools just as well as the large square Ninja. The choice depends on your preferences and the board/case that will be used with the cooler. However, both the Ninja Plus B and the Infinity are just good, quiet coolers with the shipping kit fans - they are not particularly great for overclocking. Add a quiet high output fan like the SilenX or use two Scythe fans in a push-pull configuration, and both coolers compete with the best we have tested. The Tuniq Tower 120 and Thermalright Ultra 120 still cool a bit better at most settings, but they reach the same overclock as the Ninja and Infinity with push-pull fans or a SilenX.
The Thermalright Ultra 120 Extreme remains the best air cooler we have tested so far, reaching a 3.94GHz overclock at low temperatures with a Scythe SFLEX fan. The Scythe Ninja Plus B joins the top tier of coolers just below this with the Thermalright Ultra 120, Tuniq Tower 120, OCZ Vindicator with SilenX fan, and Scythe Infinity push-pull. In any of the tested configurations it is a quiet and effective cooler, with best cooling results with a high output fan or push-pull fans.
Facebook
Twitter
RSS
36 Comments
View All Comments
Lord Evermore - Saturday, April 14, 2007 - link
How is the Ninja and Infinity "not particularly great for overclocking", when even with their stock fans, when they can hit 3.83GHz? 3.9GHz is only 66MHz higher, a whopping 1.7% higher. Individual CPU differences could easily make that up for other users, and the "better" coolers might not get an equal increase in their maximum speed in those cases. At those levels to me things seem for all intents and purposes essentially equal.With the stock fan that's a 31% overclock at 3.83G. 33% at 3.9G. Only in comparison to the very best you've tested do these come out near the lower end of the scale. Right at the end you group it together with the top tier of other coolers. And even if it was at the lower end of the "good" coolers, stock or overclocked, the actual numerical differences are so tiny as to be statistically insignificant.
I suppose 66MHz difference is a HUGE deal to rabid overclockers who are willing to spend money for it, but the majority of even enthusiasts I'd think wouldn't consider it particularly impressive given how large the stock fan overclock is. (Note I'm only addressing the frequency obtained since that seems to be the focus of what makes a cooler "good" here. Temperatures obtained at those speeds could change the lineup.)
Wesley Fink - Monday, April 16, 2007 - link
We use the exact same CPU and test bed for testing all coolers - to remove the "individual CPU" variable. But you are right to put the performance results into perspective. In the grand scheme of performance the difference in 3.83GHz and 3.90GHz is very small as you point out. There are other advantages to the very top performing coolers, however. If you check the cooling at various temps those that do 3.90GHz easily also generally provide the lowest CPU temperaturesa at any given speed.Had we devised our overclocking test a little differently and tested say, every 266 MHz - 2.93GHz, 3.2GHz, 3.466GHz, 3.633GHz, 3.80GHz, 3.966GHz - the true differences might be put in better perspective. However, we started the test with the assumption that if a cooler couldn't outperform the Intel Retail there was no point in buying it. Perhaps if the Intel Retail HSF were poorer we could show more, but the fact is the Intel Retail HSF is really very good and it takes a decent cooler to beat the one that comes at no additional cost with the Intel processor.
Your comments are fair, but we also believe our cooler test methods do identify the very top performers in the marketplace. One notch down is still pretty remarkable performance as you point out.
strikeback03 - Thursday, April 12, 2007 - link
It is kind of hard to tell in the photos, does one set of 3 heat pipes run above the other set, or are they somehow woven together so they are all approximately the same distance from the CPU? Assuming they are mounted with one set above the other, did you do any testing to see whether cooling is better with the fan mounted on one side or the other (i.e. blowing directly on the upper set of heatpipes or the lower set).Wesley Fink - Friday, April 13, 2007 - link
one group of 3 heatpipes passes through an upper plate and the other three pass through the mounting plate below. As you guessed they do cross over the lower set of heatpipes in the center of the base. We did not test with different orientations relative to the heatpipe level, but it is an interesting question.Wesley Fink - Thursday, April 12, 2007 - link
We have received the following statement from Scythe regarding the similarity of their Ninja Plus B Cooler to the OCZ Vindicator:"Scythe is a stock holder of the factory where we produce our coolers,
and also the factory is a stock holder of the Scythe Taiwan office where
we have a very tight relationship almost as close as a group company.
Within this relationship we are acknowledged and aware of all shipments
done from the factory. But OCZ is not one of them.
With the above said, we are definitely sure that OCZ coolers are manufactured
in another factory. The only components that are common between the two are the
hex caps on the heat pipes, which are supplied outside of our cooler factory.
We also have not approved OCZ's design in any form or shape, nor did we receive
any OEM request. Their products are just a simple copy of Ninja and we are
currently being troubled by this untrue rumor. "
Lord Evermore - Saturday, April 14, 2007 - link
My thought is maybe they use a different working fluid. They're just too similar in design for the hardware to have any performance difference, even if OCZ did just copy the design (if they had though, you'd think Scythe would be suing). I suppose the exact alloy composition for the base plate or other parts could be different, if they actually are made somewhere else, and then the parts just end up looking the same and being assembled in the same shape.Then again, Scythe doesn't say NOBODY gets this design but them...
ceefka - Thursday, April 12, 2007 - link
On the packaging of the Ninja it says: "supports fanless model". Now that of course will be dead silent, but it will require adequate airflow in the form of case fans. What are the temperatures and dBs in that situation?Wesley Fink - Thursday, April 12, 2007 - link
Fanless cooling seems to perform best with a PS with a downward facing exhaust fan and excellent case entry and exhaust cooling. Our test case does not really have these features, but we will definitely be paying more attention to airflow and the PS fans in choosing components for our new test bed. With the current configuration in mind, it seemed unfair to test fanless mode temps with a poor configuration for fanless cooling.We did run a quick 5-minute gaming loop at the X6800 stock speed with a fanless Ninja Plus B and it ran fine. Temps were much higher than fan configurations just as you would expect. We will be doing more in testing fanless claims in the future - once the fans are selected from testing and the new test bed is launched.
We do confess concerns over fanless given the current crop of excellent perfroming tower coolers. It appears fanless just moves the fans from the cooler to the case, but fans are still required. There are many large quiet case fans, but there are also many quiet 120mm fans for coolers these days. Fanless seemed to make more difference when ccoolers used buzzy loud 60mm and 70mm fans. These days the best coolers use heatpipes and 120mm fans and the noise levels are MUCH lower with these coolers than the screaming wonders of the past.
fic2 - Thursday, April 12, 2007 - link
I am curious about the Noise Limit heatsinks: http://www.noiselimit.com/index2.asp?id=16">http://www.noiselimit.com/index2.asp?id=16. Any chance this will be included in a review?Stele - Wednesday, April 11, 2007 - link
I'm not sure if this question has been dealt with before - my apologies if it has.I've always wondered how is it that a certain cooler can produce lower CPU temperatures but yet fail to make it at a higher CPU frequency? The Zalman CNPS9700 is a good example - at 3.83GHz the CPU runs at 40°C, which is lower than many of the others, yet does not make it to the last two CPU frequencies. A Scythe Infinity dual, however, registers 44 at the same frequency and yet makes it at least into 3.90GHz. The anomaly is even more pronounced in the stress test. In all cases the coolers seem to scale similarly, so it's not as if one of them had reached its design limit (compared to, for example, the stock Intel HSF). Has an explanation for this been given or proposed before?
I'm guessing that one factor is the mounting method. It's remarkable that some Socket-775 coolers, despite weighing some 1.5-2x that of the official 450g limit with fan, still use the stock plastic push-pin method. Without a backplate. Makes one wonder sometimes whether the cooler is indeed in good contact with the CPU, and whether after some time the cooler would fall out - or the motherboard flex and crack.