The Enermax Liberty - Getting long in the tooth, but still worth a look
by Christoph Katzer on July 30, 2007 1:40 AM EST- Posted in
- Cases/Cooling/PSUs
Testing
As usual we are testing with our Chroma programmable loads to fully load each rail to a specific amount. This is important to get truly accurate results and not merely approximate values. The tests are conducted in two different temperature environments. One is normal room temperature of 25-26°C, while the second environment goes from room temperature and increases steadily up to 50°C. Especially during the higher temperatures we will see how good the power supplies are and what they're really made of. Components inside will perform much worse at higher temperatures, but we expect any good quality PSU to deal with such test conditions without failing.
Note: If you would like to know more about our testing methodology, equipment, and environment, please read our PSU testing overview.
3.3V DC Outputs
The 3.3V rail starts at 3.4V and drops steadily with increasing load like we usually experience. Heat doesn't seem to have a great impact on the components since the voltage drop looks similar with any input voltage at any temperature. The voltage held stable within regulations and have been only close to the limit with the highest load.
5V DC Outputs
The 5V rail also starts at a high amount just like the 3.3V rail. The drop is almost constant and within specification.
As usual we are testing with our Chroma programmable loads to fully load each rail to a specific amount. This is important to get truly accurate results and not merely approximate values. The tests are conducted in two different temperature environments. One is normal room temperature of 25-26°C, while the second environment goes from room temperature and increases steadily up to 50°C. Especially during the higher temperatures we will see how good the power supplies are and what they're really made of. Components inside will perform much worse at higher temperatures, but we expect any good quality PSU to deal with such test conditions without failing.
Note: If you would like to know more about our testing methodology, equipment, and environment, please read our PSU testing overview.
3.3V DC Outputs
The 3.3V rail starts at 3.4V and drops steadily with increasing load like we usually experience. Heat doesn't seem to have a great impact on the components since the voltage drop looks similar with any input voltage at any temperature. The voltage held stable within regulations and have been only close to the limit with the highest load.
5V DC Outputs
The 5V rail also starts at a high amount just like the 3.3V rail. The drop is almost constant and within specification.
Facebook
Twitter
RSS
26 Comments
View All Comments
MCSim - Tuesday, July 31, 2007 - link
400W Liberty here. Mine is also about 2 years old and still going strong. There's no need for new PSU. :)wolfman3k5 - Monday, July 30, 2007 - link
Just out of curiosity, did you guys run out of stuff to write about?leexgx - Monday, July 30, 2007 - link
hehi had the 400W Enermax PSU for 2 years now and its powering my server quite happy (8 hdds and an old P4 2.6ghz 2gb ram) never had an problem with them (use thermaltake TR2 420W-500w now for basic PSU as its the only good ones on my local trade lists never had one blow on me)
CuriousMike - Monday, July 30, 2007 - link
fwiw, I bought two 350w enermax "basic" powersupplies about 2 years ago ( built two new machines for home.)One of the units fans developed a bad squeek about 2 months into ownership.
I tried contacting enermax in two different ways - both via email.
One was their usa (my locale) website (which I think was a distributor site?), and the other their taiwanese/chinese site.
Never heard back from them.
JarredWalton - Monday, July 30, 2007 - link
The squeaky PSU gets the new fan, and the squeaky wheel gets the oil. You just need to squeak a bit louder probably. That or you got unlucky. I haven't dealt with Enermax directly, but I have had a few companies (DFI, for example) where it took several email messages to get help. Not good at all, but eventually they did respond. The fact that their email support form fails 75% of the time didn't help, of course.Vidmar - Monday, July 30, 2007 - link
While I think the Efficiency charts in load percentage are nice, if you included Efficiency charts in watts it would be more informative from a buying perspective.The reason? I know the sum of system load is 375watts normally. The way it is now, if power supply XYZ has a max load of 650watts, I have to calculate where my ~375watts falls into that load chart (~57% load). But if the next power supply has 1000 watts max, then I have to yet again calculate what load percentage that may be for *that* power supply. If the Efficiency charts were in watts, instead of load, no calculations would be necessary. If I could look at your charts and see that XYZ power supply provided those watts the most efficiently, that would be the power supply I would get.
Maybe you could just provide a second X axis on the chart that included the watts.
Thanks!
michal1980 - Monday, July 30, 2007 - link
Owned for for probably 18+ months now. It was a replacement for the early problems the antec neo-he's had. and I bought it at a retail store for about 110 bucks. I had no idea if it was good because it was so cheap (for a retail store, everyother branded 500w psu was 150~180 bucks).its given me good stable power for all these years, and I hope for a few more.
kmmatney - Monday, July 30, 2007 - link
I've owned a 550W Enermax PSU for over 5 years! It was originally made for the old Thunder K7 dual AMD motherboards, but it now powers my Core 2 Duo. It's been a great power supply - never thought it would last so long. I did recently re-oil the fan (still running on the original fan as well).mostlyprudent - Monday, July 30, 2007 - link
Nice review. I appreciate the diversion from the high end. I have been wondering how newer models would stack up against an old favorite. It is nice to see that there is a little more happening in the PSU industry than just wattage hikes.Thinkitect - Monday, July 30, 2007 - link
Almost!Value PSU review? Quality Benchmarks? Fortron Source!
FSP Group products should be the baseline for the reviews and price/performance rating.
The AX-400 and AX-500 for value were great (and still are), though efficiency may be outdated. The blue series should be the one to compare to right now.
I've used the same AX for years through many upgrades, and it now powers a relative's workstation. I have the BlueStorm II 500 powering my new gaming rig, and now there are the FX-600-GLN and FX-700-GLN with even higher efficiency ratings.
High quality well priced components that deserve the comparison and recognition.