MultiGPU Update: Two-GPU Options in Depth
by Derek Wilson on February 23, 2009 7:30 AM EST- Posted in
- GPUs
Crysis Warhead Analysis
Crysis Warhead, the sequel to the original that follows the same story from a different perspective, does a great job of improving on the Crysis engine in terms of balancing performance and improving playability with a still-forward-looking engine (though we lack the native 64-bit runtime of the original game). We push the settings pretty high in spite of the fact that we don't turn them all the way up. Everything is set to "Gamer" quality with the exception of Shaders which are set to "Enthusiast" level.
1680x1050 1920x1200 2560x1600
Like CoD, Crysis favors NVIDIA hardware. The settings we're rocking require more than a single Radeon HD 4850 or GeForce 9800 GTX+ even at 1680x1050, so it's likely that many gamers will be running at lower settings than these. As with CoD, SLI sweeps this benchmark in terms of performance. The Radeon HD 4870 CrossFire pushes up against the GeForce GTX 260 SLI setup, but the core 216 or an overclocked GTX 260 setup would easily put some distance between them.
1680x1050 1920x1200 2560x1600
In terms of scaling, SLI looks better at lower resolutions while CrossFire puts the heat on as resolution increases. Despite the fact that the 4850 scales at over 77% (which is very good), the higher baseline of the NVIDIA cards keeps this from making the impact that it could. At the same time, configurations with two 4850 cards perform on par with the GTX 285 and offer much better value.
1680x1050 1920x1200 2560x1600
Our performance data and our value data show that in this case, AMD's approach to single card multiGPU on the high end is effective. The 4850 X2 2GB can be had from newegg for less than $300 which is more than $50 cheaper than a single GPU NVIDIA solution that gets you the same performance where it counts.
It's interesting to note that AMD two card solutions tended to scale better than the single card multi-GPU options here. Where memory is a limiter, we see our higher memory single card options scaling better. In this case, it looks like memory isn't as large a bottleneck as something else. We can't say for certain, but our guess is that it's the PCIe bus: with both cards getting a full x16 slot, each GPU is able to communicate more efficiently with the host and it seems that this is beneficial to Crysis performance.
At 1920x1200, the only single card solutions that remain playable are the GTX 280 and GTX 285. Getting good performance on a 30" monitor requires either a GTX 295 or 2x GTX 280/285s. Nothing else passes the test at the highest resolution we tested.
Facebook
Twitter
RSS
95 Comments
View All Comments
makdaddy626 - Monday, February 23, 2009 - link
I really appreciate the article and all the research and work that went into it. Kudos to you for it.A small suggestion would be to take into account a minimal playable frame rate in the value and performance per dollar data, where a ZERO would be substituted for the frame rate in instances where a card failed to reach a playable rate for a given game/resolution. I feel this would more accurately reflect the value of the card(s) as 15 FPS in most games presents no value.
Mastakilla - Monday, February 23, 2009 - link
I agreeMinimum framerates should be more important then average ones even...
Interesting article though! I didn't know the 4850x2 was so competitive...
Only in Crysis it does worse the the 285, which I had in mind for my new pc...
That does make me wonder if the 285 might be a more future proof investment...
makdaddy626 - Monday, February 23, 2009 - link
Yes, But I meant "minimum" in the sense of what the game needs to be played at, even you measure "average" - I just don't think it's fair to say that the 9800 GTX shows the highest performance per dollar on the Crysis Warhead 2560x1600 chart when it turns in frame rates of 13.5. To me that is ZERO value for the money because it's not playable. Someone wanting to play at those settings would be wasting EVERY dollar spent on the 9800 GTX.7Enigma - Tuesday, February 24, 2009 - link
Completely agree. Statistics mean nothing when not taken in a proper context. Zero, NA, or just leaving it blank would be much better. Someone looking to use that card would then click on a lower resolution and see if it is a viable choice. It would reduce the amount of data that needed to be compared as the reader of the article, and make caveats like in the explaination section about comparing between cards/resolutions etc. almost moot.Spivonious - Monday, February 23, 2009 - link
The framerate charts are all but worthless if you're focusing on how performance scales. Why not some line graphs with all three resolutions shown and card models along the x-axis? Then the reader could see how performance is affected by the lower memory of some models and how it scales linearly with the higher-end cards.7Enigma - Monday, February 23, 2009 - link
I would have to agree with this. I always enjoyed the broken line graphs that show multiple resolutions and framerates in the same graph. It makes comparisons very easy and more importantly allows EVERYONE to see their particular resolution without having to click on a link for a separate graph.It's fine to keep your specialized performance/$ and % increase from a single card the way you have it as I understand what you mean about not comparing between resolutions but for the general frame rate comparisons I preferred the old way.
One thing I failed to see which I have seen in previous reviews with X-fire/SLI (or was it with tri/quad setups?) is the stuttering that can be present. I thought it was an Anand article but could have been from another site.
SiliconDoc - Wednesday, March 18, 2009 - link
The charts are designed to autopop to 2650x - and we all know the red ragers have screamed the ati cards are great there.EVERY CHART pops to the favored ati $2,000.00 monitor resolution.
It's not an accident, Derek made them.
C'DaleRider - Monday, February 23, 2009 - link
Derek, if you want to impress, and this article does with its research, please invest in some writing manuals and learn some grammar.Take this sentence:
"This unique card really shined and held it's own all the way up to 2560x1600."
Your use of "IT'S" in this instance is incorrect. IT'S is a contraction for IT IS, not a possessive word, which is ITS.
Or take this passage, "It's very surprising to us that AMD hasn't pushed this configuration and that Sapphire are the only manufacturer to have put one of these out there."
Sapphire is a company or organization, I realize that. But in this instance, you're referring to a group in its singular fashion, or as a single unit. That context is seen by the only manufacturer in the sentence.
That sentence should have read. "It's very surprising to us that AMD hasn't pushed this configuration and that Sapphire IS the only manufacturer to have put one of these out there."
Here's the rule for that (taken from both MLA and APA handbooks): If the action of the verb is on the group as a whole, treat the noun as a singular noun. If the action of the verb in on members of the group as individuals, treat the noun as a plural noun.
This means companies, such as Microsoft, IBM, Sapphire, Ford, etc., when being referred to the company as a whole collective, single entity, has to have a singular verb.
But, if you are referring to pieces of the whole, such as "the engineers of Ford are.....", or "The programmmers at Microsoft are.....".
Please invest in some proper English grammar texts and take time to read and learn from them. Your error laden grammar you write and use is quite distracting and detracts from what is supposed to be a professionally run hardware site.
Hire a proofreader or good copy editor if learning proper grammar is too difficult.
Otherwise, this was a great article!
The0ne - Monday, February 23, 2009 - link
I don't really mind Anandtech articles as much in terms of presentation, spelling and graphics. Other sites such as Ars Technica, x-bit labs, and so forth are much worst. The first is first since they've started writing articles concerning everything, it seems.If I did mind, I say stick to the general guidelines writing manuals, procedures, pamphlets, technical docs, etc. But being online, this isn't the case and won't ever be. Again, I don't mind as much because I do the same thing myself where I hardly pay attention to spelling or grammar when writing online. It's only when I write short stories or for work that I pay attention. Strange but comfortsure does make one do these things :)
And yes, I do write all sorts of articles daily.
oldscotch - Monday, February 23, 2009 - link
"Your error laden grammar you write and use is quite distracting and detracts from what is supposed to be a professionally run hardware site."That should read "The error laden grammar you use is quite distracting..." or just "Your error laden grammer is quite distracting..."
"Your error laden grammam you write and use..." is redundant.
Perhaps you should learn some grammar yourself before criticizing others about theirs.